Skip to content

Archive for

Water Potential/Water Content:  When to Use Dual Measurements

In a previous post, we discussed water potential as a better indicator of plant stress than water content.  However, in most situations, it’s useful to take dual measurements and measure both water content and water potential.  In a recent email, one of our scientist colleagues explains why: “The earlier article on water potential was excellent.  But what should be added is an explanation that the intensity measurement doesn’t translate directly into the quantity of water stored or needed. That information is also required when managing water through irrigation.  This is why I really like the dual measurement approach. I am excited about the possibilities of information that can be gleaned from the combined set of water content, water potential, and spectral reflectance data.”

Field plantation with a sprinkler in the middle of it

Potato field irrigation

Managing Irrigation

The value of combined data can be illustrated by what’s been happening at the Brigham Young University Turf Farm, where we’ve been trying to optimize irrigation of turfgrass (read about it here). As we were thinking about how to control irrigation, we decided the best way was to measure water potential.  However, because we were in a sandy soil where water was freely available, we also guessed we might need water content. Figure 1 illustrates why.

Turf farm data concerning water potential diagram

Figure 1: Turf farm data: water potential only

Early water potential data looks uninteresting; it tells us there’s plenty of water most of the time, but doesn’t indicate if we’re applying too much.  In addition, if we zoom in to times when water potential begins to change, we see that it reaches a stress condition quickly.  Within a couple of days, it is into the stress region and in danger of causing our grass to go into dormancy.  Water potential data is critical to be able to understand when we absolutely need to water again, but because the data doesn’t change until it’s almost too late, we don’t have everything we need.

Turf farm data dual measurements data diagram

Figure 2: Turf farm data, volumetric water content only

Unlike water potential, the water content data (Figure 2) are much more dynamic. The sensors not only show the subtle changes due to daily water uptake but also indicate how much water needs to be applied to maintain the root zone at an optimal level. However, with water content data alone, we don’t know where that optimal level is. For example, early in the season, we observe large changes in water content over four or five days and may assume, based upon onsite observations, that it’s time to irrigate. But, in reality, we know little about the availability of water to the plant. Thus, we need to put the two graphs together (Figure 3).

Water potential and vol. water content diagram

Figure 3: Turfgrass data: both water potential and volumetric water content together.

In Figure 3, we have the total picture of what’s going on in the soil at the BYU turf farm. We see the water content going down and can tell at what percentage the plants begin to stress.  We also see when we’ve got too much water: when the water content is well above where our water potential sensors start to sense plant stress. With this information, we can tell that the turfgrass has an optimal range of 12% to 17% volumetric water content. Anything below or above that range will be too little or too much water.  

Soil water potential and volumetric water content diagram

Figure 4: Turfgrass soil moisture release curve (black). Other colors are examples of moisture release curves for different types of soil.

Dual measurements will also allow you to make in situ soil moisture release curves like the one above (Figure 4), which detail the relationship between water potential and water content.  Scientists can evaluate these curves and understand many things about the soil, such as hydraulic conductivity and total water availability.

Download the “Researcher’s complete guide to water potential”—>

Download the “Researcher’s complete guide to soil moisture”—>

Get more information on applied environmental research in our

Measuring Water Potential in Concrete

Trevor Dragon, a former METER Research and Development Engineer, was pouring concrete at his Beeville, Texas, farm one day and wondered if he could measure moisture in concrete with a matric potential sensor instead of the more traditionally used volumetric water content sensor (VWC) to get more accurate readings.  Dragon says, “We had about five concrete trucks come in that day, and we poured five different slabs.  Every truck had a different amount of water added.  One particular batch of concrete was really wet and soupy, and I became curious to measure it and compare it to the other slabs.”

Concrete slab drying down at Trevor's Texas farm.

Concrete slab drying down at Trevor’s Texas farm.

Why Measure Moisture in Concrete?

As concrete hardens, portland cement reacts with water to form new bonds between the components of the concrete.  This chemical process, known as hydration, gives concrete its characteristic rock-like structure.  Too much or too little water can reduce the strength of the concrete.  Adding excess water can lead to excessive voids in concrete while providing too little water can inhibit the cement hydration reaction. Thus, when you pour a slab in south Texas, where it’s exposed to high wind and intense heat, sufficient water must be added, and precautions must be taken to minimize evaporation of water from the slab surface as the concrete hardens.

Better Readings:

Dragon chose the matric potential sensor because he wondered if it would be more accurate than a VWC measurement.  He says, “I knew that VWC sensors were calibrated for soil, and because of that they would lack accuracy.  But the water potential sensor is calibrated for the ceramic it contains.  I figured it would be closer to the real thing without having to do a custom calibration.”

Moisture in concrete has been difficult to measure because the high electrical conductivity early in the hydration process throws off water content sensor calibration. So, Dragon was surprised when his data turned out to be really good.  He comments, “The dry down curve of the matric potential sensor was a perfect curve. There was a nice knee (drop from saturation) after about 200 minutes, and it just went down from there.  We’re kind of stumped because we are trying to understand why the data came out so well and why the curve looks so good.”  

MPS2 Water Potential in Concrete diagram

Water Potential in Concrete

The scientists at METER sent the drydown curve to Dr. Spencer Guthrie, a civil engineering professor, to see what he thought.  He explains, “I suspect that the concrete is experiencing initial set at around 200 minutes.  This is a very normal time frame by which finishing operations need to be complete.  At this stage in cement hydration, the concrete becomes no longer moldable.  A rigid capillary structure is forming, and individual pores are taking shape.  As hydration continues, the pores become smaller and smaller, which may explain the decrease in matric potential.”

New Methods:

One theory Dragon and his colleague Dr. Colin Campbell came up with was that perhaps Dragon’s unique method of inserting the sensors made a difference in the measurements.  He explains, “The first thing I did was look for the rebar in the concrete, and I placed the sensors in the exact center of one of the squares to avoid the influence of metal on the sensor electromagnetic field.  Also, I didn’t insert the sensors the same way you would insert them into soil.  In soil, you put the sensors in vertically; I placed the water potential sensor horizontally because in this case, I was not interested in how water was moving in the slab but how it was being used over time.

What Does It Mean for the Future?

The behavior of the water potential sensor embedded in the concrete clearly indicated a drying process where water becomes less available over time. However, the implications are still unknown.  Can the quality of the concrete be determined from the speed or extent of water becoming less available?  Hopefully, this opportunistic experiment by Dragon will lead to more tests to show whether this approach is useful to others.  

Dr. Guthrie agrees the idea should be explored further and comments, “The matric potential measurements were not redundant with the water content measurements.  Instead, they offered additional, interesting information about the early hydration characteristics of the concrete.  In the context of construction operations, the water potential data indicated what is normally determined by observing the impression left in the concrete surface from the touch of a finger.  In the context of research, however, the use of a water potential sensor may yield helpful information about how certain admixtures, for example, influence the development of hydration products in concrete over time.

Download the “Researcher’s complete guide to water potential”—>

Download the “Researcher’s complete guide to soil moisture”—>

Get more information on applied environmental research in our

Measuring Frozen Water Potential: How and Why?

In China recently, a fellow scientist asked Dr. Colin Campbell if matric potential sensors work in frozen soils.  His answer? Sort of. In this blog, he explains what he meant by his enigmatic reply: When water freezes in the soil, most matric potential sensors won’t work accurately because frozen water essentially disappears to the measurement. For example, in a dielectric measurement circuit, most of the water that was polarized in the electromagnetic field solidifies in the ice matrix. Thus, because dielectric measurements determine the charge that is stored when water is polarized, ice is not measured. But, many matric potential sensors contain a component that will measure frozen water potential: the temperature sensor.

Frozen ground with horseshoe prints

Horseshoe prints in frozen soil.

How Does Temperature Measure Water Potential?  

The temperature of a frozen matrix like soil has a fundamental thermodynamic relationship to the energy state of that water. For every one degree C below freezing, the water potential decreases by 1.2 MPa. For example, if the soil drops down to -4 C, the soil water potential will be -4.8 MPa. However, one thing many people don’t understand is that there is still liquid water in frozen soils.

Where is the Liquid Water in a Frozen Soil?

Some liquid water will always be associated with soil surfaces because water, as a polar molecule, is attracted by opposite surface charges. Ice is a collection of water molecules that have slowed enough that they are arranged in a crystal-like structure. When ice arranges in that structure, it will attract and use all those water molecules that are available but will have difficulty stealing away water bound to soil surfaces. That water will remain liquid. As soil temperature drops, water layers closer and closer to soil particle surfaces will slow and join the ice structure.

Why Worry about Frozen Water Potential?

Previously, we’ve discussed the importance of water potential in determining the availability of water for plant growth. But below freezing, plants are either dormant or expired, so why measure frozen water potential?

There are a couple of reasons frozen soil water potential may be interesting to scientists. Liquid water in frozen soil still has the possibility to move. So, knowing soil temperature will allow models to predict water flow.  

Even more interesting is what could be done with a temperature sensor and a measurement of water content using dielectric permittivity. As we mentioned earlier, ice essentially disappears to a dielectric measurement.  Thus, a dielectric sensor water content measurement should provide the amount of liquid water in the soil. Using the temperature sensor to infer water potential (assuming the soil begins wet enough that its pre-frozen state has not reduced WP significantly), we can combine the WP and VWC measurements over a range of temperatures to generate an in situ moisture release curve. This idea was developed into a prototype instrument that appeared to have promise as a new laboratory technique to obtain moisture release curves.

Download the “Researcher’s complete guide to water potential”—>

Download the “Researcher’s complete guide to soil moisture”—>

Get more information on applied environmental research in our

Water Content helps Turf Growers find Water/Nutrient Balance

Many athletes don’t like artificial turf. They say it’s hot, uncomfortable to run on, causes burns when you slide or fall on it, and changes the way a ball moves.  Professional women’s soccer players even started a lawsuit over FIFA’s decision to use artificial turf in the 2015 Women’s World Cup.

Soccer players running after the soccer ball on a green field

Soccer players on natural turf.

Some universities—including Brigham Young University—have responded to athlete concerns by using natural turf fields for practice and in their stadiums. But the challenge is to develop plants and management practices for natural turf that help it stand up to frequent use and allow it to perform well even during the difficult fall months. It’s a perfect research opportunity.

BYU turf professor and manager of BYU sports turf, Bryan Hopkins and his colleagues in the Plant and Wildlife Department, have been able to set up a new state-of-the-art facility to study plants and soil in both greenhouse and natural conditions. The facility includes a large section of residential and stadium turfgrass.  

Before Soil Sensors

Initially, BYU maintained the turf farm grass on a standard, timer-based irrigation control system, but over time they realized that understanding the performance of their turf relative to moisture content and nutrient load is crucial. Last year during Memorial Day weekend their turf farm irrigation system stopped working when no one was around to notice.  During those four days temperatures rose to 40 C (100 F), and the grass in the field slipped into dormancy due to heat stress. In response, Dr. Hopkins began imagining a system of soil moisture sensors to constantly monitor the performance of the turf grass.  He wanted not only to make sure the turf never died but also to really understand the elements of stress so they could do a better job growing healthy turf.

Sensors Give a Clear Picture

Soon afterward, a team of scientists, including fellow professor Dr. Neil Hansen, installed volumetric water content (VWC) and matric potential sensors at two different sites: one in the sports turf and one in a residential turf plot.  Each plot had two installations of sensors at 6 cm and 15 cm, along with VWC only at 25 cm, to measure water moving beyond the root zone. Combining these measurements, they could clearly see when the grass was reaching stress conditions and how quickly the turf went from the beginning of stress (in terms of water content and time) to permanent wilting point. In addition, ancillary measurements of temperature and electrical conductivity provide an opportunity for modeling surface and root zone temperature as well as fertilizer concentration dynamics.

Researcher digging a dirt canal and installing sensors

Installing water content sensors at the BYU turf farm.

Errors Revealed

What the researchers learned was that they were using too much water. Dr. Colin Campbell, a METER research scientist who worked with BYU on sensor installation, comments, “We found in the first year that the plants never got stressed at all. So this year, the researchers allowed the water potential (WP) at 6 cm to drop into the stress range (~ -500 kPa) while observing WP at 15 cm (-50 kPa to -60 kPa). We hope this approach will reduce irrigation inputs while creating some stress in the grass in order to push the roots deeper.”

What’s happening with the water?

Dr. Campbell’s favorite part of the sensor data was the detailed picture it gave of what was happening with the water in the sandy soil (Figure 1). He says, “Most people believe that they have an intuitive feel for water availability in soil.  If we were only using water content sensors, seeing a typical value of 20% would lead us to believe we were comfortably in the middle of the plant available range (A).  But in this study, using our colocated soil water content and soil water potential sensors, the data showed readings over 15% VWC were too wet to affect the WP (B). However, once WP visibly changed, it quickly moved toward critical stress levels (C, -1500 kPa is permanent wilting point); it only took two days for the water potential to change from -8 kPa to -1000 kPa.  A subsequent dry period (D) shows similar behavior, but this time the 15 cm WP drops to near -1000 kPa.”

Water potential changes diagram

Figure 1

The plant stress levels were reached surprisingly quickly in this soil because its sand composition has a lot of large pores and not very many small ones (Figure 2). Campbell explains, “The large pores store water that is not held tightly due to low surface area, so the water is freely available. But at around 10% VWC all the water from the large pores is used up. As the soil dries beyond that, the water is held tightly in small pores and becomes increasingly unavailable. This is clear in the moisture release curve.  We see almost no change in water potential as the soil dried to 16% VWC, but from 10% down to 7%, the water potential reached permanent wilting point, and it happened in just over a day.”

VWC and Water potential sensors diagram

Figure 2

What the Future Holds:

The researchers wanted to make sure that if they went down to certain stress levels, they wouldn’t cause harm to the plants, so this year, they installed a weather station to monitor evapotranspiration and calculate irrigation application rates.  They also began measuring spectral reflectance to monitor changes in leaf area (NDVI) and photosynthesis (PRI).  This will enable them to see the impact on the plants as the turf is drying down.  “In the future,” says Campbell, “we hope that both commercial and residential turf growers will be able to more effectively control their irrigation and nutrients based on what we find in this study.”

Download the “Researcher’s complete guide to water potential”—>

Download the “Researcher’s complete guide to soil moisture”—>

Get more information on applied environmental research in our

Soil Moisture and Temperature Sensors Aid Landmine Detection

Anti-personnel landmines are one of the most dangerous environmental hazards worldwide. Each year thousands of people are injured by landmines buried in eighty different countries.  Ben Wallen, Ph.D. candidate and active military officer at the Colorado School of Mines, is using soil moisture and temperature sensors to model, simulate, and predict how environmental conditions affect landmine detection performance.

Researcher and an army graduate student standing next to "The U.S Army Corps of Engineers, Engineer Research and Development Center" sign

Landmine research conducted at the Engineer Research and Development Center (ERDC) by LTC Benjamin Wallen, a graduate student at Colorado School of Mines, and Stacy Howington, a senior research engineer at ERDC.

Landmine Detection

Anti-personnel landmines are difficult to detect. They are small and often contain very little metal. It is difficult to differentiate between a landmine and, for example, a rock.

Success depends on many factors, including the landmine’s physical composition and how long it’s been in the ground. The numerical and analytical models used to find the mines rely on detailed data about conditions in the subsurface.  Wallen and his Ph.D. advisor, Dr. Kate Smits, realized that changing environmental conditions—particularly changes in soil moisture content—were commonly overlooked in developing these models. By gaining a greater understanding of these dynamic environmental conditions, Wallen thought he could better calibrate the numerical models used in detection technologies such as ground penetrating radar.

Researcher and army engineer student working on an installation site

Installing METER sensors at landmine detection field site at the Engineer Research and Development Center (ERDC) by LTC Benjamin Wallen and Matthew Geheran, a student engineer at ERDC.

Comparisons

The goal of Wallen’s research was to improve understanding of the complex flow processes of water, water vapor, and air in the shallow subsurface.  He installed soil moisture and temperature sensors in a field site in order to understand how landmines buried at different depths affect spatial patterns of soil moisture.  He compared holes with mines at a shallow depth (2.5 cm) to more deeply buried mines (10 cm).  He also measured the environmental response to shallow empty holes roughly the size that you’d dig for the placement of a mine.  He realized if there was an identifiable response between a disturbed hole with nothing in it and a hole with a mine buried, researchers would be able to do experiments with different soils in a lab without needing a buried landmine in order to investigate the environmental response associated with a buried landmine.

Results

Wallen was able to see differences in the “with mine” and “without mine” treatments.  He says, “The soil moisture in the disturbed soil 2.5 cm below the surface with no landmine inserted matched very well to a shallow-buried mine.  The only time it really deviated was when there was a saturation event. At that point, there was a break from that relationship, but then, in 36 hours, the soil moisture returned to matching very closely between the disturbed soil hole and the shallow-buried mine.”  Wallen says there was also a relationship in the case of the more deeply buried mine. He adds, “For a deeply buried mine, both the soil moisture and temperature in the disturbed soil 2.5 cm below the surface had a strong correlation with the response to the dug, disturbed hole.”

Shallow Buried Mine- Soil Moisture as a Function of Depth diagram

Disturbed and Undisturbed Soil- Soil Moisture as a Function of Depth Diagram

An Array of Sensors is Crucial

Ben says it was important to his study to use a suite of measurement tools that complimented each other.  In addition to soil moisture and temperature sensors, he used an IR camera to detect surface temperature differences prior to the saturation event, during saturation event, and then afterward, helping identify the different scenarios of shallow-buried mines, deep buried mines, and the disturbed soil. He comments, “There are numerous global climate models that may be used to predict evaporation from energy balances in order to understand what is occurring. By combining the sensors in this minefield detection scenario, we were able to really understand what was going on at different depths with soil moisture and temperature, and that enabled us to better understand how the system responds.”

The Next Step

Now that Wallen has done a soil characterization of the site, he wants to incorporate the data into a 3D model to ensure that the model accurately represents the actual physical conditions he’s observed. The next step is modeling under different climatic conditions: seeing what the environmental response is for various mine scenarios in a different soil environment.

Making the World a Safer Place

The goal, according to Wallen, is to provide pertinent information that will improve landmine detection technologies. Understanding how temperature contrast impacts remote sensing technology and understanding how the soil moisture signature impacts ground penetrating radar.  Ben says, “Ideally, this information takes us one step farther in being able to identify potential locations for landmines, but there is a long way to go. This is just one piece of the pie, but every step forward moves us toward the goal of making the world a little bit safer for everyone.”

Acknowledgments:

This research was made possible through sensors provided by Decagon (now METER), funding from the Society of American Military Engineers Denver Metro Post, field site access from the Waterways Experimentation Station (WES), and assistance with equipment and research support from scientists and engineers at the Engineer Research and Development Center (ERDC) in Vicksburg, MS. Their support and knowledge based upon over a decade of research exploring disturbed soil for threat detection and environmental effects on sensor performance was essential to enable quality research at their site.

Download the “Researcher’s complete guide to water potential”—>

Download the “Researcher’s complete guide to soil moisture”—>

Get more information on applied environmental research in our