Skip to content

Archive for

Mar 23

1 Comment

Can Wastewater Save The United Arab Emirates’ Groundwater? (Part II)

With very little recharge and irrigation comprising 75% of groundwater use, natural water resources in the United Arab Emirates region are disappearing fast (see part I).  Wafa Al Yamani and her PhD advisor, Dr. Brent Clothier, are investigating using treated sewage effluent and groundwater for irrigating the desert forests along UAE motorways.

Abu Dhabi from the ocean looking at the city

Abu Dhabi

Infiltrometers Predict Dripper Behavior:

Wafa and her team used what they call, “the Ankeny twin head method” for site evaluation with infiltrometers, and they’ve been able to use it to predict dripper behavior.  They begin with the head at -60 mm, do a series of measurements to measure steady infiltration, and repeat the process at -5 mm.  They use those measurements to solve Woodings equation which has two unknowns: saturated hydraulic conductivity and capillarity.  Dr. Clothier says, “We’ve done it at two heads, and we can use Woodings equation to solve for the slope of the exponential conductivity curve.  Hence, I can predict with time, the movement of the wetting front away from the dripper.   That’s been very useful to work out what volume of soil we’re wetting.  It tells us if we should have one or two drippers.  In this forest, we think we can get away with two drippers because if they irrigate for two hours, the radius of the wet front will be 20 cm, and the depth will be about 40 cm, which is a sufficient volume of water for the tree roots.”  Dr. Clothier says they also constructed a small dyke around the drippers so they could contain the water inside the drip zone in case of hydrophobicity or uneven sand.  

researcher recording data while sitting on the floor

Wafa on site, using the twin head method.

Treated Effluent Resolves Salinity Issues

Historically, the UAE pumped their sewage effluent into the Arabian Gulf, but recently, there has been a shift toward seeing it as a valuable water resource, not only for the desert forest, but for irrigation of fruit crops and date palms.  Dr. Clothier says, “Once we started getting our results we realized we were irrigating with groundwater that had high salinity, about 10 dS/m, and that treated sewage effluent had only 0.5 dS/m.  This was an important discovery because with the high salinity groundwater, you have to over-irrigate to maintain a salt leaching fraction.  However, when we apply the treated sewage effluent, we immediately see a response in the trees because it has 1/20th of the salt load.”

Dr. Clothier says that there is one problem with the trees responding so well to the sewage effluent.  The treated sewage effluent makes the trees grow taller and faster, so if the ecosystem service you want from the desert forest is that they’re 4-6 meters high, it becomes an issue.  He adds,”This is actually a positive problem, because we can now induce deficit irrigation, thereby creating a larger resource of treated sewage effluent in order to irrigate far more forests.”

Large white irrigation tanks sitting in sand in the desert

Researchers irrigated with water from these tanks which stored groundwater and treated sewage effluent.

What’s The Future?

Dr. Clothier says they started with a pilot study in the UAE in 2014, and it was so successful that they ended up with two fully-funded four-year projects, one on treated sewage effluent, and one investigating the irrigation of date palms. He says they have another 3 ½ years of work in the UAE on these projects, and in the end, their goal is to develop a model for forestry irrigation and soil salinity management, along with developing capability for the measurement and modeling of irrigation impacts on sustainable forestry.  They have recently developed a prototype of a computerized decision support tool for irrigation which will provide sustainable irrigation advice to optimize water use.  The support tool takes into account the need to maintain salt leaching, and actual irrigation records can be entered to enable real-time use.

Download the “Researcher’s complete guide to soil moisture”—>

Get more information on applied environmental research in our

Mar 18

1 Comment

Can Wastewater Save The United Arab Emirates’ Groundwater?

The hyper-arid United Arab Emirates (UAE) has a rapidly dwindling supply of groundwater, and that water is becoming increasingly saline.

Image of the city of Dubai at night on the coast of the UAE

Dubai is situated on the coast of the UAE.

With very little recharge and irrigation comprising 75% of groundwater use, natural water resources in this region are disappearing fast.  PhD candidate Wafa Al Yamani works for the Environmental Agency of Abu Dhabi, which has contracted with Plant and Food Research in New Zealand to investigate using treated sewage effluent and groundwater for irrigating the desert forests along their motorways.  

Sidr tree plantation in the UAE forest in the sand

Sidr trees in the UAE forest.

The Desert Forests

The UAE desalinates all the water for their cities, so the tertiary treated sewage effluent from these cities could be a viable resource, replacing some groundwater for irrigation of the desert forests. These forests perform a wide range of ecosystem services from sand stabilization along all UAE motorways to harboring a great deal of biodiversity.  There is also a cultural association with the forests.  The original ruler of the UAE, Sheikh Zayed, embarked on a program in the 1970s of “greening the desert,” so the people see the desert forests as a legacy of their founder.

Infiltrometer pushing sand and being measured

Infiltrometers were used to examine how the drip irrigation system worked.

Measuring Water Use:

Wafa and her PhD advisor, Dr. Brent Clothier, had a goal to minimize groundwater use and maximize value by quantifying the irrigation needs of the UAE’s five most important desert-forestry species.  They also wanted to determine the impact of treated sewage effluent on forest growth and health.  They used infiltrometers to examine how the drip irrigation system worked.  Dr. Clothier says, “These soils have hydraulic conductivities of between 2 and 5 meters an hour.  They are highly permeable desert sands.  We can find out how wide the bulb (the wetted area underneath an irrigation dripper) is and how deep the water will travel by using an infiltrometer to look at the hydraulic properties of the soil.”  Dr. Clothier has also developed software to predict water movement radially, with depth and with the time that the drippers are on.  He comments, “We’ve now got a setup of two drippers per tree, and we will use that in the future for modeling how the trees are taking up water from the root zone.”

Tree with 20cm dykes accessing the dripper water

Researchers built dykes of 20 cm to stop surface redistribution of dripper water.

The scientists used a heat pulse method to measure tree water-use by comparing sap flow with evaporative demand (ETo).  They used Time Domain Reflectometry (TDR) to measure soil water content, and they have developed a “light stick” using light sensors to detect the shadow area of the trees to measure trees’ leaf area in order to predict the crop factor that will enable prediction of tree water-use from ETo.

Next week:  Find out how Wafa and her team use infiltrometers to predict dripper behavior and how the treated effluent resolves salinity issues.

Download the “Researcher’s complete guide to soil moisture”—>

Get more information on applied environmental research in our

Mar 9

2 Comments

Data loggers:  To Bury, or Not To Bury (part II)

There are many reasons why you should never bury your data logger.*  Most scientists who try it, fail (see part 1).  However, there is one innovative team at Washington State University who has found a way to overcome many of the problems which plague buried data loggers. They now happily collect data from the road, sitting in the cab of a truck.

Orange plastic container with a data logger in it

The research team houses their data loggers in a water-resistant case marked with a radio ball marker and surface flagging.

Collecting Data by Radio

Caley Gasch decided she wanted to bury data loggers in an actively managed field at the Cook Agricultural Farm, so they weren’t constantly taking down data loggers for cultivation, spraying, and harvest. She says, “We wanted a better system because after we took the data loggers down, they often did not get put back up for weeks, leaving giant gaps in our data.  The idea of burying the data loggers and simply reading them by radio had crossed our minds, but we were stymied by four questions.”  

How would we bury the dataloggers so that we could find them again?  

To solve this problem, the team buried the data loggers with a radio power identifier ball, originally made by the 3M Corporation, for locating buried power lines.  She says, “It’s a radio monitor that transmits a radio signal, and we have an instrument that we can then use to find them.”  Caley buries a radio marker with the data logger so that if the flag that marks the logger location gets removed by farming equipment or the weather (which always seems to happen), she still has the ability find the buried data logger.

Orange box with cable in the port thats water and air sealed

How the cables fit through the ports.

How would we avoid filling them with water, especially on a large scale?  

Caley says she’s had success keeping water out of all but three of her forty-two data loggers. She says the shallow soil in those three locations gets easily saturated in the winter, so they are still trying to modify the system. However, the method they have developed works well for the other 39 data loggers.

Their method is to place the data loggers inside a pelican case, which is a plastic, water-tight box.  She says, “We modify the boxes so the sensor cables leaving the data logger can exit the box through cable entry connectors which we tighten down with a plastic screw.  We make a watertight seal where the cable can go in and out of the box, and we also add some heat shrink tubing on the cables themselves to tighten that connection. We put silica desiccant packs inside of the pelican box along with the data logger to keep the humidity low.  This will collect any condensation that builds up or even soak up small amounts of water that leak in.”  Caley says that any water leakage they have had is probably through the ports where they’ve modified the pelican box for cable entry, but in most locations, it’s not a problem.  

Sealed port on the orange data logger boxes

A sealed port.

How could we get radio signal to transmit out of the soil far enough?

Caley says, typically, she can connect with the radio signal up to 100 meters away from the loggers when they are buried.  She adds, “We have successfully connected to loggers that are 0.5 km away, but it depends on the landscape, the amount of water in the soil, the season, the kind of crop that’s growing, and the terrain that’s between the scientist and the data logger.  We have to get closer to most loggers.  100 meters is convenient enough for the farms that we are working on.  The roads are within that distance to each of the loggers, so we never have to actually leave the vehicle to collect our data.”

How long will the batteries last?

Caley says they’ve gotten away with only changing the batteries once a year. She usually collects data twice each year and changes the batteries in the spring.  She says, “By the time March comes around the batteries are pretty close to being dead, but we’ve been successful with just five alkaline AA batteries lasting about a year.”

One Challenge:

In some cases, the loggers haven’t been buried deep enough, and farm equipment crushed them, or the seeder penetrated the boxes.  Caley says, “We just have to make sure they are buried deep enough. We typically bury them at least 30 cm deep, and that seems to work pretty well with the current farm equipment.”

Dirt coating a data logger box sitting on top of piled up dirt

A buried data logger that has been dug up.

For the Future:

Caley has a new idea for modifying the locations that are prone to flooding.  She will keep the loggers buried most of the year, and then dig them up during the winter.   “After the harvest in the fall, when the grower gives us permission, we will go out and dig up the boxes and mount the dataloggers on a short post, so they can spend the winter above ground.  Then, after the soil has dried a little in the spring, but prior to seeding to minimize disturbance, we will bury them again.”  Caley says that even though digging them up in the winter is more work, it’s worth her time.  She concludes, “It’s still worth it to bury the loggers during the growing season so we don’t continually have data gaps while growers are seeding, spraying, or making a pass over the field.”

*Note:  METER’s (formerly Decagon) official position is that you should never bury your data logger.  But we couldn’t resist sharing a few stories of scientists who have figured out some innovative ideas which may or may not be successful if tried at other sites.

Download the “Researcher’s complete guide to soil moisture”—>

Download the “Researcher’s complete guide to SDI-12″—>

Get more information on applied environmental research in our

Mar 7

3 Comments

Data loggers: To Bury, or Not To Bury

Globally, the number one reason for data loggers to fail is flooding. Yet, scientists continue to try to find ways to bury their data loggers to avoid constantly removing them for cultivation, spraying, and harvest.  Chris Chambers, head of Sales and Support at METER always advises against it.  He warns,  “Almost all natural systems, even arid ones, will saturate at least once or twice a year—and it only takes once.”  Still…there are innovative scientists who have had some success.

A prototype buriable logger container made from a paint can with sensors attached

A prototype buriable logger container, made from a paint can, PVC elbow, silicone, epoxy putty, and desiccant. Photo Credit: NDSU | Soil Sciences | Soil Physics

The Good

Radu Carcoana, research specialist and Dr. Aaron Daigh, assistant professor at North Dakota State University, use paint cans to completely seal their data loggers before burying. They drill ports for the sensor cables, seal them up, and when they need to collect data, they dig up the cans.  Chambers comments, “So far it looks promising, but we had a long discussion about the consequences of getting any water in those cans. I don’t know what they were sealing the ports with, but they were pretty confident that they could even dunk their paint cans under water.”  The North Dakota research team buried the paint cans last fall, and Chambers says he’s reserving judgment until spring.  Radu comments, “The picture above is just the concept.  The story will continue in April when we see the North Dakota winter toll.” (See update).

The Bad

Chambers has good reason for his skepticism.  If a logger gets saturated even once, its life will be short.  And even if it doesn’t get completely flooded, there is still risk.  As water gets into the enclosure that encases the logger, the resulting high humidity can damage the instrument.  Chambers says, “If loggers that are mounted on a post get a small amount condensation or water inside, they’ll be fine.  But the buried ones have no escape route for water vapor.  If they get wet or are exposed to water vapor even once, they are going to fail. We’ve seen horror stories time and time again. It’s just not a good environment for electronics.”

Five gallon white bucket with rocks and dirt in it

One group of scientists tried burying their loggers in five-gallon buckets.

The Ugly

Chambers likes to relate a cautionary tale about some scientists in Seattle, who buried their data loggers in five-gallon buckets with lids.  They taped their loggers to the lid, but when they dug the buckets up, they were half full of water, and the loggers were dead.  This is because as the buckets filled with water, the loggers were continuously exposed to water-condensing conditions.  After the loggers were repaired, the scientists re-buried them. But, six weeks later, their buckets were again half full of water, and their loggers were dead.

One Success Story So Far

There is one innovative group at Washington State University, however, who can be considered successful.  Postdoctoral research associate Caley Gasch decided she wanted to bury data loggers in the Cook Agricultural Farm, an actively managed field, so they weren’t constantly taking down loggers and causing large gaps in their data.  

Next week: Find out how she was able to solve many of the problems that prevent successful deployment of data loggers underground.

Get more information on applied environmental research in our