Skip to content

Posts tagged ‘Measurements’

How to Protect your Soil Moisture Sensors from Lightning Surge

We occasionally see soil moisture sensors damaged by lightning.  Here’s what to do to protect them.

The secondary products of a lightning strike include electromagnetic pulses, electrostatic pulses, and earth current transients.

lighting

Surge suppression components typically perform their suppression function by temporarily short circuiting the voltage between two wires, several devices, or ground.

Electromagnetic pulses are created by the strong magnetic field that is formed by the short term current flow taking place in the lightning strike. With current flows as high as 510kA per microsecond, these currents create very large magnetic fields. These short term magnetic fields then induce voltages onto wires and cables.

Electrostatic pulses are created by electrostatic fields that accompany a thunderstorm. Any cable suspended above the earth during a thunderstorm is immersed in the electrostatic field and will be electrically charged. Quick changes in the charges stored in both the clouds and earth take place whenever there is a lightning strike. The charge on the cable must now be discharged or neutralized. Unable to find a path to ground (earth), it breaks down insulation and component in its efforts to return to earth.

Earth current transients are the direct result of the neutralization process that immediately follows the end of lightning strike. Neutralization is accomplished by the movement or redistribution of charge along or near the earth’s surface from all the points where the charge had been initially induced to the point where the lightning strike has just terminated. Earth current transients create a shift in potential across a ground plan, often called a “ground bounce”.

Read more

Soil Moisture Sensors: Which Installation Method is Best?

Patterns of water replenishment and use give rise to large spatial variations in soil moisture over the depth of the soil profile. Accurate measurements of profile water content are therefore the basis of any water budget study. When monitored accurately, profile measurements show the rates of water use, amounts of deep percolation, and amounts of water stored for plant use.

How to avoid measurement errors

Three common challenges to making high-quality volumetric water content measurements are:

  1. making sure the probe is installed in undisturbed soil,
  2. minimizing disturbance to roots and biopores in the measurement volume, and
  3. eliminating preferential water flow to, and around, the probe.

All dielectric probes are most sensitive at the surface of the probe. Any loss of contact between the probe and the soil or compaction of soil at the probe surface can result in large measurement errors. Water ponding on the surface and running in preferential paths down probe installation holes can also cause large measurement errors.

Installing soil moisture sensors will always involve some digging. How do you accurately sample the profile while disturbing the soil as little as possible?  Consider the pros and cons of five different profile sampling strategies.

Preferential flow is a common issue with commercial profile probes

Profile probes are a one-stop solution for profile water content measurements. One probe installed in a single hole can give readings at many depths. Profile probes can work well, but proper installation can be tricky, and the tolerances are tight. It’s hard to drill a single, deep hole precisely enough to ensure contact along the entire surface of the probe. Backfilling to improve contact results in repacking and measurement errors. The profile probe is also especially susceptible to preferential-flow problems down the long surface of the access tube.

Trench installation is arduous

Installing sensors at different depths through the side wall of a trench is an easy and precise method, but the actual digging of the trench is a lot of work. This method puts the probes in undisturbed soil without packing or preferential water-flow problems, but because it involves excavation, it’s typically only used when the trench is dug for other reasons or when the soil is so stony or full of gravel that no other method will work. The excavated area should be filled and repacked to about the same density as the original soil to avoid undue edge effects.

soil moisture sensors

Digging a trench is a lot of work.

Augur side-wall installation is less work

Installing probes through the side wall of a single augur hole has many of the advantages of the trench method without the heavy equipment. This method was used by Bogena et al. with EC-5 probes. They made an apparatus to install probes at several depths simultaneously. As with trench installation, the hole should be filled and repacked to approximately the pre-sampling density to avoid edge effects.

Multiple-hole installation protects against failures

Digging a separate access hole for each depth ensures that each probe is installed into undisturbed soil at the bottom of its own hole. As with all methods, take care to assure that there is no preferential water flow into the refilled augur holes, but a failure on a single hole doesn’t jeopardize all the data, as it would if all the measurements were made in a single hole.

The main drawback to this method is that a hole must be dug for each depth in the profile. The holes are small, however, so they are usually easy to dig.

Single-hole installation is least desirable

It is possible to measure profile moisture by auguring a single hole, installing one sensor at the bottom, then repacking the hole, while installing sensors into the repacked soil at the desired depths as you go. However, because the repacked soil can have a different bulk density than it had in its undisturbed state and because the profile has been completely altered as the soil is excavated, mixed, and repacked, this is the least desirable of the methods discussed. Still, single-hole installation may be entirely satisfactory for some purposes. If the installation is allowed to equilibrate with the surrounding soil and roots are allowed to grow into the soil, relative changes in the disturbed soil should mirror those in the surroundings.

Reference

Bogena, H. R., A. Weuthen, U. Rosenbaum, J. A. Huisman, and H. Vereecken. “SoilNet-A Zigbee-based soil moisture sensor network.” In AGU Fall Meeting Abstracts. 2007. Article link.

Read more soil moisture sensor installation tips.

Stem Water Content Changes Our Understanding of Tree Water Use (Part 2)

This week, we continue highlighting the second of two current research projects (see part one) which use soil moisture sensors to measure volumetric water content in tree stems and why this previously difficult to obtain measurement will change how we look at tree water use.

Tamarisk tree: an invasive species dominant in Sudan and arid parts of the United States. (Photo credit: biolib.cz)

Determining Tree Stem Water Content in Drought Tolerant Species

Tadaomi Saito and his research team were interested in using dielectric soil moisture sensors to measure the tree stem volumetric water content of mesquite trees and tamarisk, two invasive species dominant in Sudan and arid parts of the United States. Mesquite is a species that can access deep groundwater sources using their taproots which is how they compete with native species. Tamarisk, on the other hand, uses shallow, saline groundwater to survive.  The team wanted to see if dielectric probes were useful for real-time measurement of plant water stress in these drought tolerant species and if these measurements could illuminate differing tree water-use patterns.  These sensors could then potentially be used for precision irrigation strategies to assist in agricultural water management.  

Temperature Calibration Was Essential

After calibrating the soil moisture sensors to the wood types in a lab, the team inserted probes into the stems of both trees.  They also monitored groundwater and soil moisture content to try and infer whether or not the trees were plugged into a deep source of water.  Interestingly, Saito found that, unlike soil, where temperature fluctuation is buffered, tree stems are subject to large variations in temperature throughout the course of the day.  This temperature fluctuation interfered with the soil moisture probes’ ability to accurately measure VWC.   The team came up with a simple method for accounting for temperature variability and were then able to obtain accurate VWC measurements.  

stem water content

Photo credit: desertusa.com

Water Use Depended on Landscape Position

Saito’s results were similar to Ashley Matheny’s study (see part 1), in that they found a lot of different patterns, even in trees of the same species.  Water-use depended on where the trees were on the landscape.  Some of them were tapped into groundwater, and the stem water storage didn’t change no matter how dry the soil became.  Whereas others, depending on their position in the landscape, were very dependent on soil moisture conditions.  

You can read the full study details here.

Implications

Saito’s study illustrates that we see everything about a tree that’s above ground, but we may have no sense of what’s going on below ground.   We can put a soil moisture sensor in the ground and decide there’s plenty of moisture available.  Or if conditions are dry, we may decide the tree is under drought stress, but we don’t know if that tree is tapped into a more permanent source of groundwater.   

Other researchers have put soil moisture sensors in orchards looking at stem water storage from a practical standpoint for irrigation management.  Their data didn’t work out so well because of cable sensitivity where water on the cable created false readings.  However, the data they were able to obtain showed that some of the trees were plugged into water sources that were independent of the soil.  Those trees were able to withstand drought and needed less irrigation, whereas other trees were much more sensitive to soil moisture.  

If we had an inexpensive, easy to deploy measurement device plugged into every tree in an orchard, we could irrigate tree by tree, give them precisely what they needed, and account for their unique situation.

What Does it All Mean?

The interesting thing about using soil moisture sensors in a tree is that stem water content is a difficult to obtain piece of information that has now been made easier.  Historically, we’ve focused on measuring sap flow, but that’s just how much water is flowing past the sensor. We’ve measured what’s in the soil: a pool of moisture that’s available to the tree. But some trees are huge in size, such as ones along the coast of California. They’re able to store vast amounts of water above-ground in their tissue.  Understanding how a tree can use that water to buffer or get through periods of drought is a unique research topic that has had very little attention. With these kinds of sensors, we can start to investigate those questions.

Reference: Saito T., H. Yasuda, M. Sakurai, K. Acharya, S. Sueki, K. Inosako, K. Yoda, H. Fujimaki, M. Abd Elbasit, A. Eldoma and H. Nawata , Monitoring of stem water content of native/invasive trees in arid environments using GS3 soil moisture sensor , Vadose Zone Journal , vol.15 (0) (p.1 – 9) , 2016.03

Get more information on applied environmental research in our

Avocado Growers in Kenya Fight Drought with Recycled Water Bottle Irrigation (Part 2)

Dr. Brent Clothier, Dr. Steve Green, Roberta Gentile and their research team from Plant and Food Research in New Zealand are working in Kenya to alleviate the poverty of the many small-holder farmers who grow avocados in the Central Highlands of Kenya (see part 1). This week, read about an inexpensive irrigation solution for these farmers and how the researchers are developing a plan to manage nutrients.

avocado

The period of water stress in October is at the time of main flowering.

Recycled Water Bottles Provide a Solution

When the team was visited Kenya in early March, the Long Rains had not arrived, and the trees were under water stress. The researchers sought to reduce the impact of drought by using a prototype of a portable drip-irrigation system they developed. They used ‘old’ 20 liter drinking water bottles to deliver water to the trees at 4 L/hr.

avocado

20 L water bottles used for tree irrigation.

The bottles can be refilled and moved from tree to tree. By measuring water content in the soil, the team found that the 20 L of drip irrigated water lasted in the soil about 2 days. When the period was increased to 4 days, the root water uptake was reduced over days 3 and 4 after wetting. Thus they recommended the bottle be recharged and reapplied every two days. This enables the bottle to be used on another tree on the intervening day and should help the farmers to reduce the worst impacts of the drought while waiting for the Long Rains to arrive.

avocado

Refilling the water bottles.

Replacing Low Soil Nutrients

In another phase of the experiment, Dr. Clothier’s team surveyed soil and plant nutrient contents in the main avocado production regions to assess the current fertility status of the farms. Soils in this region are classified as Nitisols, deep red soils with a nut-shaped structure and high iron content (Jones et al. 2013). These soils have low levels of organic matter and low pH. Soil sampling revealed a decrease in pH and increase in organic matter with altitude in the Kandara valley. This observed gradient is likely attributable to the higher amounts rainfall received in the higher altitudes of the valley, which can increase organic matter production and leach base cations from the soil. Soil and leaf nutrient analyses of the monitoring farms showed similar trends in nutrient availability. There are also low levels of the macronutrients nitrogen and phosphorus and the micronutrient boron in these soils. These nutrients are essential for avocado growth and production. One challenge to improve avocado productivity is finding ways to improve soil nutrient availability and tree nutrition.

avocado

An example of the benefits of a secure revenue-stream: One farmer purchased a new cow, which enables him to meet the nutrient requirements of more avocado trees.

A Plan for Managing Nutrients

The majority of the small-holder farms supplying avocados to Olivado use organic production methods. This means organic amendments such as plant residues, composts and animal manures are required to replenish the nutrients that are exported from the farms and improve soil fertility. Livestock have the potential to provide nutrient amendments for a considerable number of avocado trees. Even better, the input of organic materials will build-up soil organic matter levels, which benefit soil conservation, water holding capacity, pH buffering, and soil biological activity.

The researchers are developing simple nutrient budgets for these avocado trees using yield and fruit nutrient concentration data to assess the quantity of nutrients being exported off-farm in the harvested crop. Using the nutrient concentrations of locally available organic amendments, they will provide recommendations on the amount of organic material needed to sustain soil fertility.

Nutrient balances will be incorporated into a decision support tool to assist small-holder farmers in enhancing their soil and plant nutrition. These budgets will be enhanced by further characterizing the nutrient composition and quantities of available organic matter amendments in the region. The researchers are working to improve these nutrient budget estimates with data specific to the avocado farms in the region. They will also set up demonstration farms to evaluate the production responses to recommended nutrient management practices.

To find out more about Kenyan avocado research contact Brent Clothier: brent.clothier@plantandfood.co.nz .

(This article is a summary/compilation of several articles first printed in WISPAS newsletter)

References:

Jones, A., Breuning-Madsen, H., Brossard, M., Dampha, A., Deckers, J., Dewitte, O., Gallali, T., Hallett, S., Jones, R., Kilasara, M., Le Roux, P., Micheli, E., Montanarella, L., Spaargaren, O., Thiombiano, L., Van Ranst, E., Yemefack, M., Zougmore, R., (eds.) 2013. Soil Atlas of Africa. European Commission, Publications Office of the European Union, Luxembourg. 176 pp.

Get more information on applied environmental research in our

 

Avocado Growers in Kenya Fight Drought with Recycled Water Bottle Irrigation

Dr. Brent Clothier, Dr. Steve Green, Roberta Gentile and their research team from Plant and Food Research in New Zealand are working in Kenya to alleviate the poverty of the many small-holder farmers who grow avocados in the Central Highlands of Kenya. These farmers have old and very large avocado trees. The fruit from these trees are purchased by the company Olivado EPZ who presses over 1300 small-holders’ avocados for oil. Dr. Clothier and his team are investigating how to increase the productivity of the farmers’ avocado trees and increase the quality of the fruit so they yield more oil.

avocado

Small-holder farmers grow avocados in the Central Highlands of Kenya.

Reducing Leaf Area to Avoid Water Stress

Because of the age and size of these trees, harvesting of the avocados is difficult and time consuming, and through dropped fruit, the quality of the avocados can be comprised. In addition, any dry season water-stress negatively impacts fruit filling. The research team performed some initial remedial pruning of these trees to develop a more manageable and productive tree form. They sought to assess whether the reduced leaf area would enable the trees to avoid water stress during the dry season of January through March between the short and long rainy seasons. They removed 30-40% of the central limbs of the avocado tree to create a more open canopy form.

The team instrumented two trees with heat-pulse sap-flow probes. One tree was left unpruned and the tree in the photo above was pruned. The tree that was pruned was using between 300-400 liters per day, as expected for a tree of that large size. The unpruned tree was smaller in size, and it was using between 150-250 liters per day during May and June. The selective limb pruning resulted in the rate of water-use dropping to 200-300 liters per day, a drop of 100 liters per day.

avocado

The more open canopy form of the pruned avocado tree.

Determining Tree Water Use During Rainy and Dry Seasons

The team also measured the water-use of four trees of different sizes during the entire season using the compensation heat-pulse method and soil water content. They found the trees’ water-use doubled with the arrival of the Short Rains and then began to decline in early January after the rains ended. The trees were under a degree of water stress prior to the arrival of the (short) Short Rains, and as the weak Short Rains ended early, the trees again went into water stress with only occasional respite due to isolated rainstorms in January and February.

This pattern of water stress presents a challenge for sustaining high levels of avocado production. The period of water stress in October is at the time of main flowering, and researchers who were there noted a carpet of aborted flowers on the orchard floor. They also noticed that the fruit were smaller at one farm than those higher up in the Central Highlands where rainfall is higher and more frequent. Thus, to improve production it is imperative to mitigate the impacts of drought, and this needs to be done without reference to any infrastructure for irrigation.

Next week: Read about an inexpensive irrigation solution for these farmers and how the researchers are developing a plan to manage nutrients.

(This article is a summary/compilation of several articles first printed in WISPAS newsletter)

Get more information on applied environmental research in our

 

Soil Moisture Sensors: Why TDR VS. Capacitance May Be Missing the Point (Part 2)

Dr. Colin S. Campbell discusses whether TDR vs. capacitance (see part 1) is the right question, the challenges facing soil moisture sensor technology, and the correct questions to ask before investing in a sensor system.

It’s easy to overlook the obvious question: what is being measured?

What are You Trying to Measure?

When considering which soil water content sensor will work best for any application, it’s easy to overlook the obvious question: what is being measured?  Time Domain Reflectometry (TDR) vs. capacitance is the right question for a researcher who is looking at the dielectric permittivity across a wide measurement frequency spectrum (called dielectric spectroscopy). There is important information in these data, like the ability to measure bulk density along with water content and electrical conductivity. If this is the desired measurement, currently only one technology will do: TDR. The reflectance of the electrical pulse that moves down the conducting rods contains a wide range of frequencies.  When digitized, these frequencies can be separated by fast fourier transform and analyzed for additional information.

The objective for the majority of scientists, however, is to simply monitor soil water content instantaneously or over time, with good accuracy. There are more options if this is the goal, yet there are still pitfalls to consider.

capacitance

Considerable research has been devoted to determining which soil moisture sensors meet expectation.

Each Technology Has Challenges

Why would a scientist pay $100+ for a soil volumetric water content (VWC) sensor, when there are hundreds of soil moisture sensors online costing between $5 and $15? This is where knowing HOW water content is measured by a sensor is critical.

Most sensors on home and garden websites work based on electrical resistivity or conductivity. The principle is simple: more water will allow more electrons to flow. So conductivity will change with soil water content. But, while it’s possible to determine whether water content has changed with this method, absolute calibration is impossible to achieve as salts in the soil water will change as the water content changes. A careful reading of sensor specs will sometimes uncover the measurement method, but sometimes, price is the only indication.

Somewhere between dielectric spectroscopy and electrical resistance are the sensors that provide simple, accurate water content measurement. Considerable research has been devoted to determining which of these meet expectation, and the results suggest that Campbell Scientific, Delta-T, Stevens, Acclima, Sentek, and METER (formerly Decagon Devices), provide accurate sensors vetted by soil scientists. The real challenge is installing the sensors correctly and connecting them to a system that meets data-collection and analysis needs.

Installation Techniques Affect Accuracy

Studies show there is a difference between mid-priced sensor accuracy when tested in laboratory conditions. But, in the field, sensor accuracy is shown to be similar for all good quality probes, and all sensors benefit from site specific soil calibration. Why? The reason is associated with the principle upon which they function. The electromagnetic field these sensors produce falls off exponentially with distance from the sensor surface because the majority of the field is near the electrodes. So, in the lab, where test solutions form easily around sensor rods, there are differences in probe performance.  In a natural medium like soil, air gaps, rocks, and other detritus reduce the electrode-to-soil contact and tend to reduce sensor to sensor differences. Thus, picking an accurate sensor is important, but a high quality installation is even more critical.

capacitance

Improper installation is the largest barrier to accuracy.

Which Capacitance Sensor Works Best?

Sensor choice should be based on how sensors will be installed, the nature of the research site, and the intended collection method. Some researchers prefer a profile sensor, which allows instruments to be placed at multiple depths in a single hole. This may facilitate fast installation, but air gaps in the auger pilot hole can occur, especially in rocky soils. Fixing this problem requires filling the hole with a slurry, resulting in disturbed soil measurements. Still, profile sensor installation must be evaluated against the typical method of digging a pit and installing sensors into a side-wall. This method is time consuming and makes it more difficult to retrieve sensors.

New technology that allows sensor installation in the side of a 10 cm borehole may give the best of both worlds, but still requires backfill and has the challenge of probe removal at the end of the experiment.

The research site must also be a consideration. If the installation is close to main power or easily reached with batteries and solar panels, your options are open: all sensors will work. But, if the site is remote, picking a sensor and logging system with low power requirements will save time hauling in solar panels or the frustration of data loggers running out of batteries.

capacitance

Often times it comes down to convenience.

Data Loggers Can Be a Limitation

Many manufacturers design data loggers that only connect to the sensors they make. This can cause problems if the logging system doesn’t meet site needs. All manufacturers mentioned above have sensors that will connect to general data loggers such as Campbell Scientific’s CR series. It often comes down to convenience: the types of sensor needed to monitor a site, the resources needed to collect and analyze the data, and site maintenance. Cost is an issue too, as sensors range from $100 to more than $3000.

Successfully Measure Water Content

The challenge of setting up and monitoring soil water content is not trivial, with many choices and little explanation of how each type of sensor will affect the final results. There are a wealth of papers that review the critical performance aspects of all the sensors discussed, and we encourage you to read them. But, if soil water content is the goal, using one of the sensors from the manufacturers named above, a careful installation, and a soil-specific calibration, will ensure a successful, accurate water content measurement.

For an in-depth comparison of TDR versus capacitance technology, read: Dielectric Probes Vs. Time Domain Reflectometers

For an understanding of how capacitance sensors compare to other major contemporary sensor technologies, watch our Soil Moisture 201 webinar.

Improved Methods Save Money in Future Borehole Thermal Energy Storage Design

Globally, the gap between the energy production and consumption is growing wider. To promote sustainability, University of California San Diego PhD candidate and ASCE GI Sustainability in Geotechnical Engineering committee member, Tugce Baser, Dr. John McCartney, Associate Professor, and their research team, Dr. Ning Lu, Professor at Colorado School of Mines and Dr. Yi Dong, Postdoctoral Researcher at Colorado School of Mines, are working on improving methods for borehole thermal energy storage (BTES), a system which stores solar heat in the soil during the summer months for reuse in homes during the winter. Baser says, “We are running out of finite energy resources. We need to come up with new strategies to use free and renewable energy resources such as solar energy for a sustainable future.”

borehole thermal energy storage

Baser’s BTES design.

How it works

BTES systems are an approach to provide efficient renewable resource-based thermal energy to heat buildings. They are configured to store thermal energy collected from solar thermal panels during the summer and discharge the heat to buildings during the winter. They function by circulating a fluid within a closed-loop pipe network installed in vertical boreholes to inject heat collected from solar thermal panels. During winter, cold fluid is circulated through the heat exchangers to recover the heat from the subsurface and distribute it to the buildings. Baser explains, “The subsurface provides an excellent medium to store this heat due to the relatively lower thermal conductivity and lower specific heat capacity especially when the soil layer is in the vadose zone. Lower thermal properties allow us to concentrate the heat in a specific array and the heat losses to the environment are potentially low. These systems typically include an insulation layer and a hydraulic barrier near the ground surface to reduce heat and vapor losses to the atmosphere.”

borehole thermal energy storage

BTES construction.

Why do we need improved methods?

Baser and her team are trying to improve the understanding of heat storage mechanisms and evaluate changes in the rate of heat transfer and heat storage in the vadose zone where the soil is unsaturated. The goal of the project is improve conventional methods by generating models to fit different soil types and situations.  She says, “The European community introduced us to the borehole thermal energy storage systems to provide heat specifically for domestic use, but there is still a chance for us to design them more efficiently by having a full understanding of the thermal response of these systems that is specific to the ground material and subsurface conditions. The primary objective of this research is to understand the mechanisms of coupled heat transfer and water flow in unsaturated soil profiles during the heat injection and subsequent heat extraction into these different arrays and different dimensions of borehole heat exchangers.”

borehole thermal energy storage

Solar panels.

Baser and her team working on designing numerical models based on finite element method which improve some of the numerical models in the literature used to characterize the thermal response of the systems. The new models add new considerations, such as the heat pipe effect in different soil types. Baser explains, “Because thermal and hydraulic properties of soils are highly coupled and are specific to soils, the thermal response of a BTES system will be different when it is installed in different types of soils. For example, you see the heat pipe effect where there is evaporation and subsequent condensation in fine grained soils rather than coarse soils because in coarse grain soils the pore characteristics are different. The duration of the heat pipe effect (or convective cycle) is longer in fine grain soils. We conclude that considering coupled heat transfer and water flow in the thermal response of Borehole Thermal Energy Storage system is important.”

borehole thermal energy storage

In-ground heat exchanger

Experiments in the field and in the lab help verify the new models

To fully understand heat transfer mechanisms and water flow in unsaturated soils, the research team installed two different SBTS systems at different scales, one in Golden, Colorado School of Mines campus, and the other at the UC San Diego research campus.  Baser says, “The subsurface characteristics of both sites are different, and this gives us the opportunity to investigate the impact of the different soil layers on the thermal response experimentally in a full scale. In addition, the scales of each Borehole Thermal Energy Storage system are different, and we also apply different heat injection rates. We have used these data to further validate our coupled heat transfer and water flow model so that we can use it for design purposes.”

borehole thermal energy storage

Soil moisture sensor locations.

Baser started with laboratory heating experiments, in which soil in a large tank is heated by heat exchangers. She installed soil moisture sensors to measure volumetric water content and the temperature and then used the KD2 pro thermal property analyzer to monitor thermal properties during heating experiments to characterize the coupled thermo-hydraulic relationships. For the field experiments the team uses soil moisture sensors equipped with temperature sensors and the KD2 pro to monitor subsurface temperature fluctuation because during the summertime the air temperature is higher, thus ambient air temperature fluctuation and penetration may become significant.

Baser also uses thermistor strings that include six thermistors at different depths and thermistor pipe plugs, voltage input modules, and flow meters.  She says, “Thermistor pipe plugs and flow meters are used in the manifold to monitor the inlet and outlet fluid temperatures and flow rates in each loop to calculate heat transfer rate into the ground. Flow meters were installed to control flow in each loop because you don’t want to over or underload the borehole loops. The amount of energy that you collect from the solar loop and the amount of energy that you inject into the ground can be used to define the efficiency of the system.” Baser says thermistor strings help monitor the ground temperature during the summer heat loading at different depths. They’re also used to monitor borehole wall temperature over time. The team installed one thermistor string 9 meters away from the heat storage array to see if far field is affected by the heat transfer within the array.

borehole thermal energy storage

Insulation prevents heat loss to the environment.

The new models will save money in future Borehole Thermal Energy Storage design

Baser says building numerical models and solving them was very complicated and time consuming, but they’ve had good results. She explains, “We’ve recently proved, both experimentally and numerically, that considering coupled thermal and hydraulic relationships are very important for thermal response analysis. Thus, our recommendation is that it’s fine to use the analytical models and user-friendly numerical models that consider constant thermal properties in the design analyses for saturated soils. However, in unsaturated soils, there is a very high possibility that the contribution of heat transfer evaporation and condensation would be missing and the Borehole Thermal Energy Storage system would be oversized, costing a significant amount of money. When dealing with soils in the vadose zone, coupled thermo-hydraulic constitutive relationships in the modeling efforts need to be considered.”

You can learn more about Tugce Baser’s research here.

Get more information on applied environmental research in our

 

Soil Moisture Sensors: Why TDR vs. Capacitance May Be Missing the Point

Time Domain Reflectometry (TDR) vs. capacitance is a common question for scientists who want to measure volumetric water content (VWC) of soil, but is it the right question?  Dr. Colin S. Campbell, soil scientist, explains some of the history and technology behind TDR vs. capacitance and the most important questions scientists need to ask before investing in a sensor system.

TDR vs. Capacitance

TDR began as a technology the power industry used to determine the distance to a break in broken power lines.

Clarke Topp

In the late 1970s, Clarke Topp and two colleagues began working with a technology the power industry used to determine the distance to a break in broken power lines.  Time Domain Reflectometers (TDR) generated a voltage pulse which traveled down a cable, reflected from the end, and returned to the transmitter. The time required for the pulse to travel to the end of the cable directed repair crews to the correct trouble spot. The travel time depended on the distance to the break where the voltage was reflected, but also on the dielectric constant of the cable environment.  Topp realized that water has a high dielectric constant (80) compared to soil minerals (4) and air (1).  If bare conductors were buried in soil and the travel time measured with the TDR, he could determine the dielectric constant of the soil, and from that, its water content.  He was thus able to correlate the time it took for an electromagnetic pulse to travel the length of steel sensor rods inserted into the soil to volumetric water content. Despite his colleagues’ skepticism, he proved that the measurement was consistent for several soil types.

TDR vs. Capacitance

TDR sensors consume a lot of power. They may require solar panels and larger batteries for permanent installations.

TDR Technology is Accurate, but Costly

In the years since Topp et al.’s (1980) seminal paper, TDR probes have proven to be accurate for measuring water content in many soils. So why doesn’t everyone use them? The main reason is that these systems are expensive, limiting the number of measurements that can be made across a field. In addition, TDR systems can be complex, and setting them up and maintaining them can be difficult.  Finally, TDR sensors consume a lot of power.  They may require solar panels and larger batteries for permanent installations. Still TDR has great qualities that make these types of sensors a good choice.  For one thing, the reading is almost independent of electrical conductivity (EC) until the soil becomes salty enough to absorb the reflection.  For another, the probes themselves contain no electronics and are therefore good for long-term monitoring installations since the electronics are not buried and can be accessed for servicing, as needed.  Probes can be multiplexed, so several relatively inexpensive probes can be read by one set of expensive electronics, reducing cost for installations requiring multiple probes.

Many modern capacitance sensors use high frequencies to minimize effects of soil salinity on readings.

Advances in Electronics Enable Capacitance Technology

Dielectric constant of soil can also be measured by making the soil the dielectric in a capacitor.  One could use parallel plates, as in a conventional capacitor, but the measurement can also be made in the fringe field around steel sensor rods, similar to those used for TDR.  The fact that capacitance of soil varies with water content was known well before Topp and colleagues did their experiments with TDR.  So, why did the first attempt at capacitance technology fail, while TDR technology succeeded? It all comes down to the frequency at which the measurements are made.  The voltage pulse used for TDR has a very fast rise time.  It contains a range of frequencies, but the main ones are around 500 MHz to 1 GHz.  At this high frequency, the salinity of the soil does not affect the measurement in soils capable of growing most plants.  

Like TDR, capacitance sensors use a voltage source to produce an electromagnetic field between metal electrodes (usually stainless steel), but instead of a pulse traveling down the rods, positive and negative charges are briefly applied to them. The charge stored is measured and related to volumetric water content. Scientists soon realized that how quickly the electromagnetic field was charged and discharged was critical to success.  Low frequencies led to large soil salinity effects on the readings.  This new understanding, combined with advances in the speed of electronics, meant the original capacitance approach could be resurrected. Many modern capacitance sensors use high frequencies to minimize effects of soil salinity on readings.  

TDR vs. Capacitance

NASA used capacitance technology to measure water content on Mars.

Capacitance Today is Highly Accurate

With this frequency increase, most capacitance sensors available on the market show good accuracy. In addition, the circuitry in them can be designed to resolve extremely small changes in volumetric water content, so much so, that NASA used capacitance technology to measure water content on Mars. Capacitance sensors are lower cost because they don’t require a lot of circuitry, allowing more measurements per dollar. Like TDR, capacitance sensors are reasonably easy to install. The measurement prongs tend to be shorter than TDR probes so they can be less difficult to insert into a hole. Capacitance sensors also tend to have lower energy requirements and may last for years in the field powered by a small battery pack in a data logger.   

In two weeks: Learn about challenges facing both types of technology and why the question of TDR vs. Capacitance may not be the right question.

Get more information on applied environmental research in our

Where Will the Next Generation of Scientists Come From?

The Global Learning and Observations to Benefit the Environment (GLOBE) Program is an international science and education program that provides students and the public worldwide with the opportunity to participate in data collection and the scientific process.

GLOBE

GLOBE has a huge impact in schools around the world.

Its mission is to promote the teaching and learning of science, enhance community environmental literacy and stewardship, and provide research quality environmental observations.  The GLOBE program works closely with agencies such as NASA to do projects like validation of SMAP data and the Urban Heat Island/Surface Temperature Student Research Campaign.  The figure below shows the impact GLOBE is having in schools worldwide.

Dixon Butler, former GLOBE Chief Scientist, is excited about the recent African project GLOBE is now participating in called the TAHMO project.  He says, “Right now, in Kenya and Nigeria, GLOBE schools are putting in over 100 new  mini-weather stations to collect weather data, and all that usable data will flow into the GLOBE database.”

GLOBE

Participating in real science at a young age gets youth more ready to be logical, reasoning adults.

Why Use Kids to Collect Data?

Dixon says kids do a pretty good job taking research quality environmental measurements.  Working with agencies like NASA gets them excited about science, and participating in real science at a young age gets them more ready to be logical, reasoning adults.  He explains, “The 21st century requires a scientifically literate citizenry equipped to make well-reasoned choices about the complex and rapidly changing world. The path to acquiring this type of literacy goes beyond memorizing scientific facts and conducting previously documented laboratory experiments to acquiring scientific habits of mind through doing hands-on, observational science.”

Dixon says when GLOBE started, the plan was to have the kids measure temperature.  But one science teacher, Barry Rock, who had third grade students using Landsat images to do ozone damage observations, called the White House and said, “Kids can do a lot more than measure temperature.” He gave a presentation at the White House where he showed a video of two third grade girls looking at Landsat imagery. They were discussing their tree data, and at one point, one said to the other, ‘That’s in the visible. Let’s look at it in the false color infrared.’  At that point, Barry became the first chief scientist of GLOBE, and he helped set up the science and the protocols that got the program started.

GLOBE

GLOBE uses online and in-person training and protocols to be sure the students’ data is research quality.

Can GLOBE Data be Used by Scientists?

GLOBE uses online and in-person training and protocols to be sure the students’ data is research quality.  Dixon explains, “There was a concern that these data be credible, so the idea was to create an intellectual chain of custody where scientists would write the protocols in partnership with an educator so they would be written in an educationally appropriate way.  Then the teachers would be trained on those protocols. The whole purpose is to be sure scientists have confidence that the data being collected by GLOBE is useable in research.”

Today GLOBE puts out a Teacher’s’ Guide and the protocols have increased from 17 to 56.  The soil area went from just a temperature and moisture measurement to a full characterization.  Dixon says, “We’ve been trying to improve it ever since, and I think we’re getting pretty good at it.”  

GLOBE

GLOBE students were the only ones going around looking up at the sky doing visual categorization of clouds and counting contrails. It was just no longer being done, except by these students.

What About the Skeptics?

If you ask Dixon how he deals with skeptics of the data collected by the kids, he says, “I tell them to take a scientific approach.  Check out the data, and see if they’re good.  One year, a GLOBE investigator found a systematic error In U-tube maximum/minimum thermometers mounted vertically, which had been in use for over a century, that no one else found. The GLOBE data were good enough to look at and find the problem.  There are things the data are good for and things they’re not good for. Initially, we wanted these data to be used by scientists in the literature, and there have been close to a dozen papers, but I would argue that GLOBE hasn’t yet gotten to the critical mass of data that would make that easier.”

GLOBE did have enough cloud data, however, to be used in an important analysis of geostationary cloud data where the scientist compared GLOBE student data with satellite data Dixon adds, “GLOBE students were the only ones going around looking up at the sky doing visual categorization of clouds and counting contrails. It was just no longer being done, except by GlOBE students. Now GLOBE has developed the GLOBE Observer app that let’s everyone take and report cloud observations.”

GLOBE

Young minds need to experience the scientific approach of developing hypotheses, taking careful, reproducible measurements, and reasoning with data.

What’s the Future of GLOBE?

Dixon says GLOBE’s goal is to raise the next generation of intelligent constituents in the body politic. He says, “I thought about this a lot when I worked for the US Congress.  In addition to working with GLOBE, I now have a non-profit grant-making organization called YLACES with the objective of helping kids to learn science by doing science.  Young minds need to experience the scientific approach of developing hypotheses, taking careful, reproducible measurements, and reasoning with data. Inquiries should begin early and grow in quality and sophistication as learners progress in literacy, numeracy, and understanding scientific concepts. In addition to fostering critical thinking skills, active engagement in scientific research at an early age also builds skills in mathematics and communications. These kids will grow up knowing how to think scientifically. They’ll ask better questions, and they’ll be harder to fool.   I think that’s what the world needs, and I see the environment and science as the easiest path to get there.”

Learn more about GLOBE and its database here and about YLACES at www.ylaces.org.

Get more information on applied environmental research in our

New Weather Station Technology in Africa-3

The Trans African Hydro and Meteorological Observatory (TAHMO) project expects to put 20,000 microenvironment monitors over Africa in order to understand the weather patterns which affect that continent, its water, and its agriculture. In the conclusion of our 3 part series, we  interview Dr. John Selker about his thoughts on the project.

TAHMO

The economics of weather data value may be going up because we’re reaching a cusp in terms of humanity’s consumption of food.

In your TEDx talk you estimate that US weather stations directly bring U.S. consumers  31 billion dollars in value per year. Can Africa see that same kind of return?

Even more.  The economics of weather data value may be going up because we’re reaching a cusp in terms of humanity’s consumption of food.  Africa, one could argue, is the breadbasket for this coming century.  Thus, the value of information about where we could grow what food could be astronomical.  It’s very difficult to estimate.  One application of weather data is crop insurance.  Right now, crop insurance is taking off across Africa. The company we’re working with has 180,000 clients just in Kenya.  When we talked about 31 billion dollars in the U.S., that is the value citizens report, but you need to add to that protection against floods, increased food production, water supply management, crop insurance and a myriad of other basic uses for weather data.  In Africa, the value of this type of protection alone pays for over 1,000 times the cost of the weather stations.

Another application for weather data is that in Africa, the valuation of land itself is uncertain. So if, because of weather station data, we find that a particular microclimate is highly valuable, suddenly land goes from having essentially no value to becoming worth thousands of dollars per acre.  It’s really difficult to estimate the impact the data will have, but it could very well end up being worth trillions of dollars.  We have seen this pattern take place in central Chile, where land went from about $200/hectare in 1998 to over $3,000/ha now due to the understanding that it was exceptionally suited to growing pine trees, which represented a change in land value exceeding $3 billion.

Does the effect of these weather stations go beyond Africa?

There’s limited  water falling on the earth, and if you can’t use weather data to invest in the right seeds, the right fertilizer, and plant at the right time in the right place, you’re not getting the benefit you should from having tilled the soil.  So for Africa the opportunity to improve yields with these new data is phenomenal.  

In terms of the world, the global market for calories is now here, so if we can generate more food production in Africa, that’s going to affect the price and availability of food around the world.  The world is one food community at this point, so an entire continent having inefficient production and ineffective structures costs us all.

TAHMO

If we can generate more food production in Africa, that’s going to affect the price and availability of food around the world.

You’re collecting data from Africa. Is it time to celebrate yet?

I think this is going to be one of those projects where we are always chilling the champagne and never quite drinking it.  It is such a huge scope trying to work across a continent.  So I would say we’ve got some stations all over Africa, we’re learning a lot, and we’ve got collaborators who are excited.  We have reason to feel optimistic.  It will be another five years before I’ll believe that we have a datastream that is monumental.  Right now we’re still getting the groundwork taken care of.  By September of this year we expect to have five hundred of stations in place, and then two years from now, over two thousand. This will be a level of observation that will transform the understanding of African weather and climate.

TAHMO

This is a project of hundreds of people across the world putting their hands and hearts in to make this possible.

How do you deal with the long wait for results?  

In science there is that sense you get when you want to know something, and you can see how to get there.  You have a theory, and you want to prove it.  It kind of captures your imagination.  It’s a combination of curiosity and the potential to actually see something happen in the world: to go from a place where you didn’t know what was going on to a place where you do know what’s going on.  I think about Linus Pauling, who made the early discoveries about the double helix.  He had in his pocket the X-ray crystallography data to show that the protein of life was in helical form, and he said, “In my pocket, I have what’s going to change the world.”  When we realized the feasibility of TAHMO, we felt much the same way.”  

Sometimes in your mind, you can see that path: how you might change the world.  It may never be as dramatic as what Pauling did, but even a small contribution has that same excitement of wanting to be someone who added to the conversation, who added to our ability to live more gracefully in the world.  It’s that feeling that carries you along, because in most of these projects you have an idea, and then ten years later you say, “why was it that hard?”  

Things are usually much harder than your original conception, and that energy and curiosity really helps you through some of the low points in your projects.  So, curiosity has a huge influence on scientific progress.  Changing the world is always difficult, but the excitement, curiosity, and working with people, it all fits together to help us draw through the tough slogs.  In TAHMO, I cannot count the number of people who have urged us to keep the effort moving forward and given a lift just when we needed it most.  This is a project of hundreds of people across the world putting their hands and hearts in to make this possible.  Having these TAHMO supporters is an awesome responsibility and concrete proof of the generosity and optimism of the human spirit.

Learn how you can help TAHMO.

%d bloggers like this: